Function & correspondence of the wires:

Left commodo:

High commodo:

The user manual

This manual only corresponds to commodos Remmotorcycle. It contains important remarks about safety and manipulation. Read the instructions carefully, in particular the safety instructions, in their integrality before using the switching unit on your vehicle. Failure to comply with this manual can cause vehicle damage, affect road safety or cause accidents.

Immerate this user manual for subsequent use. If you give up the unit From switching to a third party, please transmit this user manual to the corresponding person.

Security

Use consistent

THE characteristics of push buttons :

250VAC 3A - IP45

The characteristics of switches:

0.5A 50V DC; Resistance: 30mΩ max, isolation resistance: 100mΩ min at 500V DC; Resistance voltage: AC 500V for 1 min

Commodos are universal. The mounting possibilities depend on compatibility with the handlebars and with other electronic components.

Safety instructions

This product represents a danger to children and people whose physical, sensory or mental capacities are reduced (e.g. people with partial or elderly handicap whose physical and mental capacities are restricted) or people who do not have No experience or knowledge required (e.g. older children).

Keep the packaging film as well as the small parts that are part of the equipment supplied out of the reach of children. Risk of asphyxiation.

Risk of short-circuit

The electrical installation and the mechanical assembly on the vehicle must be carried out in a compliance. Incorrect assembly can cause short circuits or dysfunctions of the on-board electrical system.

During assembly, imperatively respect the information contained in the user manual of the vehicle or in a maintenance and repair manual corresponding to the model, as well as the specifications of the vehicle manufacturer and the user manual of the control module used.

Before carrying out the work on the vehicle's electrical system, imperatively disconnect the vehicle battery.

No traction force should be exerted on electric cables, even when the management is completely robbed. They must be passed so as to be protected, not to be stuck and not to undergo friction or folds. 

Risk of injury

During the assembly work, make sure that the vehicle is perfectly stable and that the workplace is well lit.

Assembly

Preparation

Raise your vehicle safely (using a workshop crutch or the central vehicle crutch) in a clean and well -lit place. The battery must be disconnected before starting the work (disconnect the cable less).

Assembly

1. Remove the handles, accelerator handles and old commodos.
2. Loosen the two M3 of Commodos screws. The 2 parties must remain linked. 
3. Slide the commodos to their location. (Rings are to be removed for the menu in 25mm / 1 ").
4. You can tighten the M3 screws at the back of the commodos.
5. Connect the cables to the electric bundle of the motorcycle using the connection diagrams at the top of the page.

Risk of short circuit!

Connect the switching unit in accordance with the corresponding connection diagram, as well as the control diagram of the control module of the control by electronic button. To do this, scrupulously respect the instructions contained in the assembly instructions of the control by electronic button. Assign the terminals more and less to the corresponding controlled function in accordance with the patterns.

Once the cables have been connected, the battery disconnected must be reconnected. The vehicle ordered electrical functions can now be checked.

Storage

Keep the switching unit not yet mounted in the original packaging in a closed room sheltered from bad weather and humidity.

Cleaning and maintenance

Clean the switching unit with hot soapy water or with a motorcycle cleaner and a soft cloth. Never use a cleaning product that can attack aluminum.

Legal warranty

This product is covered by the legal guarantee of two years. The warranty period begins from the date of purchase. Any sign of wear, any non -compliant use or for purposes other than those provided, any damage due to an accident, handling or attempted repair by customer service or an unauthorized person or any modified product on the technical plan are excluded from the warranty.

Contact

For any questions concerning the product and/or these instructions, please contact, before the first use of the product, our Center S.A.V. by e-mail at the address: contact@remmotorcycle.com 

We will help you as soon as possible. In this way, we guarantee a correct use of the product together.